Connections and Valves

  1. Tri-Clamp Blank
    $7.95

    Tri-Clamp Blank

    A stainless steel plate to close, or blank off an outlet. Sometimes it is referred to as a blind cap.

    Currently available in these sizes:
    - 1.5" (3.81cm)
    - 2" (5.08cm)
    - 3" (7.62cm)

  2. Tri-Clamp Cap to Camlock Adapter Tri-Clamp Cap to Camlock Adapter
    $16.95

    Tri-Clamp Cap to Camlock Adapter

    A 1.5" tri-clamp cap to male camlock adapter.

  3. 2 Inch Tri Clover Stainless Mesh Screen PTFE (Teflon)
    $15.95

    2 Inch Tri Clover Stainless Mesh Screen PTFE (Teflon)

    This Stainless Mesh Screen has a PTFE (Teflon) seal integrated around the outside of it.  The hard PTFE compount is highly chemical and heat resistant.  This can be used as a standard seal or alternatively it can be used as a filter screen preventing the flow of large prticulates going through your tri-clover fittings.

    This fitting is often used for distillation to retain packing medial or used in pot distillation to retain botanicals in the vapour stream.

    Out of Stock
  4. Tri-Clamp Cap - 4" to 1.5" Reducer Tri-Clamp Cap - 4
    $27.95

    Tri-Clamp Cap - 4" to 1.5" Reducer

    4 Inch to 1.5 Inch Tri-Clamp Reducer.

    This is a 1.5 and 4 inch tri-clamp that will fit most standard 1.5 inch and 4 inch tri-clamp hardware.

    The tri-clamp system has been a common connection type in the food processing industry and medical industry as its easy to clean, sanitary and no threads are exposed to the product contained in the fittings.

  5. Tri-clamp Cap 1.5" with 25mm Barb Tri-clamp Cap 1.5
    $14.95

    Tri-clamp Cap 1.5" with 25mm Barb

    A stainless steel Tri-Clamp Cap with a 25mm (1") Barb fitting. Great for yeast dumping with Ss Brewmaster Chronicals.

    - 304 stainless steel 
    - 1.5" tri-clamp 
    - 1" OD hose barb

  6. Tri-Clamp Cap - 6" to 3" Reducer Tri-Clamp Cap - 6
    $59.95

    Tri-Clamp Cap - 6" to 3" Reducer

    Tri-Clamp Cap - 6" to 3" Reducer. Great for 10 Gal Brite Tanks or 52/76L Unitanks.

    Note: gaskets not included, but you can find them here.

  7. Keg Lube
    $9.95

    Keg Lube

    Clear lubrication gel for keg parts such as o-rings, couplers, party pumps. Use with plastic and rubber components to avoid cracks and extend their life. Just a little of this goes a long way.
    Out of Stock
  8. FermZilla Tri-Conical - 2" x 2" Tri-Clamp Butterfly Valve FermZilla Tri-Conical - 2
    $49.95

    FermZilla Tri-Conical - 2" x 2" Tri-Clamp Butterfly Valve

    Compatible with any 2 Inch tri-clamp fitting. Primarily designed for the:
    FermZilla 2" Tri-Clamp Lid
    - in conjunction with the 2" Tri-Clamp Hop Bong

    If you are looking to put your FermZilla Tri-Conical / All Rounder in a Fermentation Chamber / Fridge, you will want to allow 420mm measured from the base of the ring collar to a comfortable level to pull the pressure relief valve to purge oxygen from the hop bong.

  9. Duotight - 9.5mm One Way Check Valve (Gas)
    $6.95

    Duotight - 9.5mm One Way Check Valve (Gas)

    This elbow piece is suitable for the EVABarrier Beer & Gas line in 9.5mm (3/8") OD line to 6.3mm (1/4") ID.

  10. Grainfather G70 1/2" Tee
    $14.10

    Grainfather G70 1/2" Tee

    Replacement 1/2" Tee for the G70